Electronics are epoxy encapsulated for protection against vibration, dust, water and for thermal dissipation purposes – Control Terminals – M3 threaded contacts, tin plated brass, 304 stainless steel hardwareĬonstruction – Manufactured using corrosion resistant materials throughout. – Switch Terminals – M8 threaded stud, tin plated copper, 304 stainless steel hardware Remote emergency combine switch input 12V – marked REM Main negative input for sensing 0V – marked NEGĪlert trigger indicator output 12V – marked IND – Auxiliary (second) batter positve – marked AUX BATT – Main (starting) battery positive – marked MAIN BATT
#Smart battery isolator override wire manual
Refer to manual for detailed information on setting the EBI Pro parameters. The user interface consists of a 3 digit LED display, 6 set point indicators and 2 control buttons. User Interface – the user or operator interface is used to control and monitor the various functions of the EBI Pro.
– High voltage disconnect – automatic reconnect – Under voltage disconnect – automatic reconnect – Electrical overload protection – automatic reset – Thermal overload shutdown – automatic reset Humidity should not exceed 90%.Įnvironmental Protection – Electronics sealed for dust and water protection to IP67 rating (internal components only) – Add up to 30mA for external LED indicator if connectedĮnvironmental considerations – Operating temperature range is -25 degree C to +60 degree. – Add ~ 10mA when LED Status Display is active – In ‘Combine’ mode (closed contacts) <40mA – In ‘Isolate’ mode (open contacts) <30mA Indicator Output Signal – 30mA maximum (current limited) Surge Rating – 500 Amps DC at <50 degrees C for a period of 5 seconds 10% duty cycleĬontact Resistance – across switch terminals <2.0 milli ohm 25 degrees C Time Delay – both the COMBINE and ISOLATE time delay limits are user adjustable in 1 second increments from 1 to 250 secondsĪlert Voltage – the ALERT! voltage limits are user adjustable in 0.1 Volt increments from 9.0 Volts to 15.9 VoltsĬonstant Rating – 100 Amps DC continuous 60 degrees C ambient temperature – The ISOLATE (off state) voltage limits are user adjustable in 0.1 Volt increments from 9.0 Volts to 15.8 Volts – The COMBINE (on state) voltage limits are user adjustable in 0.1 Volt increments from 9.2 Volts to 16.0 Volts Topology – solid state Mosfet (metal oxide semiconductor field-effect transistor) switching circuitĪpplication – for 12VDC in-vehicle dual battery installations only Corrosion resistant construction and hardware.Insulated rubber terminal protection boots.Under/over voltage automatic disconnect.Automatic electrical overload protection.Counter Charge Control feature (see manual).Remote output for mode indication (LED light).Emergency Combine Mode for back-up starting.500 Amp peak rating (100 Amps continuous).High visibility LED status display and indicators.In short, the EBI Pro is designed to provide years of service – isn’t that what you want from a dual battery controller? That’s higher than most manufacturers rate their batteries! The device is environmentally sealed and the MOSFETs are epoxy encapsulated. It has been designed for under bonne installations and will run 100 Amps continuously at 60 degrees C. The EBI Pro is built for Australian conditions – seriously. This provides the instaler or operator with the means to customize the EBI Pro for the application rather than suffer the ‘one size fits all’ philosophy from manufacturers of traditional devices. Like its big brother the PSR, the EBI Pro is also adjustable in terms of voltage and time delay. The solid state aspect is just the beginning. Reliability, durability and longevity are built in. The MOSFET based topology of the EBI Pro is proven. That is, no contacts to vibrate, chatter, arc, wear and ultimately – fail. Unlike conventional electro-mechanical isolators the EBI Pro is solid state. Based on the solid foundation of our ground-breaking Programmable Voltage Sensing Relay (PSR) the EBI Pro has been designed from the ground up for 4WD and RV applications. The EBI Pro is a revolution in dual battery control devices.
INTERVOLT EBI PRO 100 AMP BATTERY ISOLATOR with OVER RIDE SWITCH
0 kommentar(er)
